Avaya/Lucent Partner ACS Systems...
Note: Your system may be pre-programmed from the factory for automatic Daylight Saving Time changes according to the OLD Daylight Saving Time schedule (1st Sunday of April thru the last Sunday of October). If you manually change the time according to the NEW Daylight Saving Time schedule (2nd Sunday of March thru the 1st Sunday of November), and discover that your system is ALSO automatically changing the time according to the OLD schedule, please deactivate the automatic feature per the below instructions.
How to deactivate the Automatic Daylight Savings Time feature:
- From extension 10 or 11, press [ FEATURE ] [ 0 ] [ 0 ]
- Press the LEFT intercom button twice
- Dial [ # ] [ 1 ] [ 2 ] [ 6 ]
- The default setting is 1 (active). To deactivate, dial 2
- Exit from System Administration [ FEATURE ] [ 0 ] [ 0 ]
How to manually set the time:
- Log in to the PARTNER ACS system in the System Administration mode from extension 10 or 11, press [ FEATURE ] [ 0 ] [ 0 ]
- Press the LEFT intercom button twice
- Dial [ # ] [ 1 ] [ 0 ] [ 3 ]
- Enter the new time in 24-hour notation. For example, to set the time to 2:15pm, press [ 1 ] [ 4 ] [ 1 ] [ 5 ]
- Exit from System Administration [ FEATURE ] [ 0 ] [ 0 ]
This is a multi-step process which involves entering administrator level programming and then setting the date and time. Programming can only be done from a 12 or 24 button display telephone.
- With your handset on-hook, press TRSF and then dial 200. Your display then showsENABLE CUS. PROG. PASSCODE:
- Dial your 4-digit pass code 1234 (which is the default pass code). The display then shows ENABLE CUS. PROG. DISABLE. If the pass code 1234 does not work as stated, please see Samsung DCS Notes below.
- Dial 1 to enable. The display now shows ENABLE CUS. PROG. ENABLE.
- Press TRSF and the display will return to its idle condition. Now that you have entered administrative level programming, you must begin programming within 30 seconds. Any delay of more than 30 seconds between keystrokes will cause the system to automatically exit the programming mode.
- Next enter the new date and time as follows:
Press TRSF and then dial 505. The display then shows the current date and time setting on your system. The example below shows Monday, April 7, 2003, 9:30 AM. - OLD: 0 04 07 03 : 09 30
NEW:WMMDDYY:HHMM. - Enter the correct date using the dial pad as follows:
W= Day of the week (0-6; Week begins on Monday and ends on Sunday)
MM= Month (01-12)
DD= Day of the month (01-31)
YY= Last two digits of the year (01)
HH= Hour (Use 24 hour clock and enter the range of 00-23)
MM= Minutes (00-59)
Press TRSF to store and exit programming. If you have entered invalid data, you will receive an INVALID ENTRY message for three seconds. Reenter the date and time.
The new date and time will now be updated for all LCD phones on the system. Some internal voice mail systems use this time and date setting. These include SVMi-4, SVMi-8, and Cadence voice mail systems. Other voice mail systems must be set independently from the telephone system. We have listed instructions for several popular voice mail systems above.
Samsung DCS Notes: 1234 is the default pass code for entering customer programming. The system administrator can change this code if desired. If the code has been changed, please input the new code instead of 1234.
This is a multi-step process which involves entering administrator programming and then setting the date and time. Programming can be done from any display telephone.
- Enter administrator level programming with your handset on-hook, press #06. Your display then shows MMC DISABLED.
- Dial your 4-digit pass code 4321 (which is the default pass code), followed by 1#. At this time, customer programming is enabled. If the pass code 4321 does not work as stated, please see Prostar 816 Plus Notes.
- Next enter the date and time, press #55 and the display will show:
(YY MM DD W HH MM) - Enter new information as follows:
YY= Last two digits of the year (01)
MM= Month (01-12)
DD= Day of the month (01-31)
W= Day of the week (1-7; Week begins on Monday and ends on Sunday)
HH= Hour (Use 24 hour clock and enter the range of 00-23)
MM= Minutes (00-59) - Dial # to finish setting the date and time. The phone now returns to normal use and all display phones have been updated to the correct date and time by this action. Voicemail systems must be set independently from the telephone system. We have listed instructions for several popular voice mail systems above.
Prostar Plus Notes: 4321 is the default code for entering customer programming. The system Administrator can change this code if desired. If the code has changed, please input the new code here instead of 4321. This program only works on the Prostar 816 Plus, and not the Prostar 816H.
This is a multi-step process which involves entering administrator programming and then setting the date and time. Programming can be done from any display telephone.
- Enter administrator level programming with your handset on-hook, press #04. Your display then shows MMC DISABLED.
- Dial your 4-digit pass code 4321 (which is the default pass code), followed by 1#. At this time, customer programming is enabled. If the pass code 4321 does not work as stated, please see Prostar 816H Notes.
- Next enter the date and time, press #55 and the display will show:
(YY MM DD W HH MM) - Enter new information as follows:
YY= Last two digits of the year (01)
MM= Month (01-12)
DD= Day of the month (01-31)
W= Day of the week (1-7; Week begins on Monday and ends on Sunday)
HH= Hour (Use 24 hour clock and enter the range of 00-23)
MM= Minutes (00-59) - Dial # to finish setting the date and time. The phone now returns to normal use and all display phones have been updated to the correct date and time by this action.
Prostar 816H Notes: 4321 is the default code for entering administrator programming. The system Administrator can change this code if desired. If the code has changed, please input the new code here instead of 4321. This program only works on the Prostar 816H, and not the Prostar 816 Plus.
This is a multi-step process which involves entering administrator programming and then setting the date and time. Programming can be done from any display telephone.
- Enter administrator level programming with your handset on-hook, press #20. Your display then shows (OPEN SYSTEM PGM- ENTER CODE:).
- Dial your 4-digit pass code 4321 (which is the default pass code), the display then shows (OPEN SYSTEM PGM- CLOSED). If the pass code 4321 does not work as stated, please see Prostar 56/1224 Notes.
- Press the MUTE key and the display will show (OPEN SYSTEM PGM- OPEN).
- Press # and your phone returns to idle condition. You must begin programming within 60 seconds. Once in programming, any delay of more than 60 seconds between keystrokes will cause the system to automatically close programming.
- Dial #70 and the display shows (YY MM/DD HH:MM).
- Enter the current date and time as follows:
YY= Last two digits of the year
MM= Month (01 for January through 12 for December)
DD= Day of the month (01-31)
W= Day of the week (1-7; Week begins on Monday and ends on Sunday)
HH= Hour (Use 24 hour clock--Failure to enter time in 24 hour clock will cause the date to change at 12:00 noon.)
MM= Minutes (00-59) - Dial # to store and exit. The phone now returns to normal use and all display phones have been updated to the correct date and time by this action. If invalid data is entered, you will receive the (INVALID ENTRY) message for three seconds. Reenter the correct date and time. Should the information entered be incorrect, please repeat the procedure.
Prostar 5EX/1224 Notes: 4321 is the default code for entering administrator programming. Some systems have reversed this to 1234. Please try this if 4321 does not work. What's more, the system Administrator can change this code if desired. If the code has changed, please input the new code here instead of 4321.
Note: Your system is pre-programmed from the factory for automatic Daylight Saving Time changes according to the NEW Daylight Saving Time schedule (2nd Sunday of March thru the 1st Sunday of November), and should should correctly advance 1 hour in the Spring and revert back 1 hour in the Fall.
This process will set the time in the display of your telephones and in the voicemail system.
- While the phone is idle, press #83
- Dial two digits for the hour (24 hour clock, 13 = 1:00 PM)
- Dial two digits for the minutes (00-59)
- Dial two digits for the seconds (00-59)
- Press HOLD
- Dial two digits for the Month (MM)
- Dial two digits for the Day (DD)
- Dial four digits for the Year (YYYY)
- Press HOLD
- Press SPK
Note: Your system is pre-programmed from the factory for automatic Daylight Saving Time changes according to the NEW Daylight Saving Time schedule (2nd Sunday of March thru the 1st Sunday of November), and should should correctly advance 1 hour in the Spring and revert back 1 hour in the Fall.
This process will set the time in the display of your telephones and in the voicemail system.
- Press SPK
- Dial 828
- Dial two digits for the hour (24 hour clock, 13 = 1:00 PM)
- Dial two digits for the minutes (00-59)
- Press SPK to hang up
Note: Your system may be pre-programmed from the factory for automatic Daylight Saving Time changes according to the OLD Daylight Saving Time schedule (1st Sunday of April thru the last Sunday of October). If you manually change the time according to the NEW Daylight Saving Time schedule (2nd Sunday of March thru the 1st Sunday of November), and discover that your system is ALSO automatically changing the time according to the OLDschedule, please call National Telesystems for assistance.
This process will set the time in the display of your telephones and in the voicemail system.
- Press SPK
- Dial 828
- Dial two digits for the hour (24 hour clock, 13 = 1:00 PM)
- Dial two digits for the minutes (00-59)
- Press SPK to hang up
To set the time and date for your i-Series system:
- From the System Administrator's telephone (normally extension 301), press CALL1 and dial 828.
- Dial the Time and Date password.
The password is normally 0000. - Dial two digits for the year (e.g., 05).
- Dial two digits for the month (01-12).
- Dial two digits for the day (01-31).
- Dial the day of the week (0-6).
0=Sunday, 6=Saturday - Dial two digits for the hour (24 hour).
For example, 13=1:00 PM. - Dial two digits for the minutes (00-60).
You hear confirmation beeps. - Press SPK to hang up.
Note: Some systems may be pre-programmed from the factory for automatic Daylight Saving Time changes according to the OLD Daylight Saving Time schedule (1st Sunday of April thru the last Sunday of October). If you manually change the time according to the NEWDaylight Saving Time schedule (2nd Sunday of March thru the 1st Sunday of November), and discover that your system is ALSO automatically changing the time according to the OLDschedule, please call National Telesystems for assistance.
The Time and date are to be set from the first attendant station. (The default for this station is extension 100).
- Dial 692 on the dial pad
- Enter Time and Date in the following format: YY MM DD HH MMYY= Year (01)
MM= Month (01-12)
DD= Day (01-31)
HH= Hour (00-23)
MM= Minute (00-59) - When the correct number of digits are entered, confirmation tone will be heard.
Performing this operation will adjust the time setting on all display phones.
Please Note! The Time and date are to be set from the first attendant station. (The default for this station is extension 100).
- Press ON/OFF button
- Dial 76 on the dial pad
- Enter time and date as follows: YY MM DD HH MM
YY= Year (01)
MM= Month (01-12)
DD= Day (01-31)
HH= Hour (00-23)
MM= Minute (00-59) - Press HOLD
Performing this operation will adjust the time setting on all display phones.
Note: The time can only be set from an assigned display phone or Station 10. On a WIN 100D, time is to be set from the Receptionist phone. Performing this operation will adjust the time setting on all display phones.
- Press FEAT button
- Dial 32
- Dial 4 Digit Hour
- Dial * for AM or Dial # for PM
- Press FEAT button
- Press HF button
- Press the Voicemail button on your phone. This is normally labeled Voicemail or VM.
- Press 8 to return to the main greeting.
- Dial **456# to enter Administrative Programming.
- At the "Enter Function" prompt, dial 320# .
- After playing the current time, the system will prompt you through entering the new time. Be sure to enter 1 for AM or 2 for PM.
- Press # to confirm.
- Press # again until the prompt says "Enter Function".
- At the "Enter Function" prompt, dial 111# to exit programming.
- Press Voicemail button.
- When asked to enter your passcode, dial *.
- When you hear the main greeting, press * again.
- When asked for your mailbox number, enter 999.
- Enter Access Code. Enter 9876.
- From the Mailbox Owner's Menu, dial 9 to reach the Administrative Options Menu.
- Dial 3 for system configuration.
- Dial 3 to set the time.
- Follow prompts as instructed.
- First access or enter your voice mailbox
- Dial 7 to enter Administrative Options
- Enter the administrator password 2275 is the default password for administrator access
- Dial 8 - System Administration
- Dial 4 - Set Time / Date, system then plays current system date and time
- Enter the two-digit month, 01 through 12. Press * to go back or # to cancel
Type in the two-digit month. (01=January, 02=February, 03=March, etc.)
If you press # the system will re-ask for the month
If you press * the system will send you to the Setup Lines menu - Please enter the two-digit day, 01 through 31.Press * to go back or # to cancel
Type in the two-digit day
If you press # the system will re-ask for the month
If you press * the system will send you to the Setup Lines menu. - Please enter the four-digit year. Press * to go back or # to cancel
Enter the four digit year
If you press # the system will re-ask for the day
If you press * the system will send you to the Setup Lines menu. - Please enter the two-digit hour, 00 through 23. Press # to go back or * to cancel
Enter the time in a 24 hour clock format (13=1:00pm)
If you press # the system will re-ask for the year
If you press * the system will send you to the Setup Lines menu. - Please enter the two-digit minute, 00 through 59. Press * to go back or # to cancel". 13) Enter the minute of the hour. If you press # the system will re-ask for the hour. If you press * the system will send you to the Setup Lines menu.
- Press # to confirm or * to cancel.
The system will now tell you the new date and time set and ask you to confirm what you have entered. If you press # the system's date and time will be saved and the system will reset itself. If you press * then the system will send you to the Setup Lines menu.
- Dial into voice mail.
- Dial # followed by the System Administrator Mailbox number:
# + 0 = 2 Digit mailbox system
# + 00 = 3 Digit mailbox system
# + 000 = 4 Digit mailbox system
The system will announce: “Mailbox 15-0”, which is the System Administrator Mailbox number. - When requested, enter Administrator password. 9#56 is the default password for administrator access.
- Dial 4 - Set Time / Date.
- Dial 2 to change data.
- After the first prompt, enter the time in four-digit military time format e.g., 0930 for 9:30 A.M. or 1830 for 6:30 P.M.
- After the second prompt, enter the date as a six-digit number in MMDDYY format. You are then returned to the prompt that asks if you want to review data, change data, or exit.
- Press ** to exit system.
IMPORTANT... This is a multi-step process which involves entering administrator programming and then setting the date and time. Programming must be done from a professional display telephone. The term "soft key" mentioned below refers to the buttons just below the LCD display.
- With the handset on-hook, press Feature # * and your display will then prompt you for the pass code.
- Enter your pass code. (The default pass code is 0 0 0 0 0 0).
- Press the SHOW soft key and the display will then read 1. SET
- Press the NEXT soft key 3 times until 4. RESOURCE appears in the display.
- Press the SHOW soft key.
- Press the NEXT soft key 9 times until SYSTEM TIME appears in the display.
- Press the SHOW soft key and the year appears in the display.
(If you simply wish to change the hour for Daylight Savings Time, you may press NEXT repeatedly to bypass the YEAR, MONTH, DAY, and WEEKDAY, and skip directly to step 15). - Press the CHG soft key followed by the 4-digit year.
- Press the SAVE soft key followed by the NEXT soft key and the month appears in the display.
- Press the CHG soft key to change the month. This is a toggle changing process (JAN/FEB/.../DEC) followed by the SAVE soft key.
- Press the NEXT soft key and the 2-digit day will appear.
- Press the CHG soft key enter the 2-digit date followed by the SAVE soft key.
- Press the NEXT soft key and the weekday appears in the display (MON/TUE/.../SUN). This is a toggle changing process followed by the SAVE soft key.
- Press the NEXT soft key and the 2-digit hour appears in the display.
- Press the CHG soft key and enter the 2-digit hour followed by the SAVE soft key.
- Press the NEXT soft key and the 2-digit minute appears in the display.
- Press the CHG soft key and enter the 2-digit minute followed by the SAVE soft key.
- Press the RLS button to exit programming.
IMPORTANT... Time and date are set at the Master station (#20) only and the information is shown on all of the Executive stations on the system. When setting or resetting of either Time or Date is required, always set both Time and Date. NOTE: Neither # nor * keys are used in programming Time and Date.
- Press the SET TIME key and the display will show HH-MM (Hour-Minute).
- Enter the 4 digit time and press the AM/PM key for PM only. As an example, to enter 2:05 PM, press 0 2 0 5 and the AM/PM key.
- Press the SET TIME key and the display will now show the correct time on all executive phones.
- Press the ALARM key and your display will show MM-dd-YY (Month-Day-Year).
- Enter the 6 digit year and press the SET TIME key. To see the date, press the DATE key or wait for a short time and the display will automatically return to Time.
Posts
